Exams Subjects Test Series PYQ Free MCQs

Log in Register

Exams Subjects Test Series PYQ Free MCQs Register free

Loading…

Civil Engineering MCQ practice, mock tests and performance analysis for SSC JE, RRB JE, GATE, ESE and State AE/JE exams.

Exams

SSC JE Civil
RRB JE Civil
GATE Civil
UPSC ESE Civil
GPSC AE Civil

Practice

Free MCQs with answers
Civil subjects
SSC JE previous year papers
All previous year papers
Test series
Free tests

Civexa

About
Contact
Terms of Use
Privacy Policy
Refund Policy
Create free account

© 2026 Civexa. Questions are original or used with permission; official papers are credited to their exam bodies.

Transportation Engineering MCQs with Answers & Solutions — Page 5 | Civexa

Subjects / Transportation Engineering / MCQs

Free questions

Transportation Engineering MCQs with answers

296 free questions — page 5 of 6. Open one to see the correct answer and the full solution.

As per IRC, the bridge approach should have a minimum straight length of _______ on either side of bridge.Bridge Engineering
The minimum clearance from the edge of the bearing plate to the pier edge should be not less than _______Bridge Engineering
If maximum design discharge is 0.3 m3/sec, then the vertical clearance required for Road Bridge above the HFL is _______Bridge Engineering
The tracked vehicle loading specified under IRC Class AA originated due to the loading pattern of _______Bridge Engineering
Cross drainage structure with waterway in the range of 6m to 30m is known as _______Bridge Engineering
Which of the following statement(s) is/are correct with respect to the Nagpur Road Plan? (i) It classifies the roads of the country into 5 categories…Transportation Planning
Which of the following methods of road construction suggested that heavy foundation stones are not at all necessary to be placed at the bottom of the…Highway Materials
For estimating the optimum road length by saturation system, which of the following factor(s) is/are considered for obtaining utility per unit length…Transportation Planning
On roads with restricted width or on single lane roads, when two-way movement of traffic is permitted, the minimum stopping sight distance should be…Sight Distance
If the calculated superelevation works out to be less than the camber of the road surface, then the minimum superelevation required for effective…Geometric Design
Which of the following statement(s) is/are correct regarding flexible pavement design methods? (i) McLeod method is based on empirical approach (ii)…Pavement Design
The relationship between Modulus of subgrade reaction (K), pressure sustained (p) and displacement (∆) is expressed as ________Pavement Design
Which of the following statement(s) is/are correct regarding selection of bridge site location? (i) Map study is used to identify the approximate…Bridge Engineering
Which of the following statement(s) is/are incorrect regarding coefficient of friction? (i) It decreases for smooth pavement (ii) It decreases for…Geometric Design
For estimating the total reaction time of the driver through PIEV theory, the time required for the driver to understand the situation is called asTraffic Engineering
Consider ‘h/2’ is the height of the center of gravity of the vehicle above the road surface, ‘b’ is the width of the wheel base and ‘f’ is the…Geometric Design
The required psychological widening for a horizontal curve of radius 225 m, width of pavement 7.5 m, longest wheelbase of the vehicle expected is 6.7…Geometric Design
If the length of transition curve is 60 m, radius of curve is 200 m and the design speed is 80 kmph, then the shift of transition curve is ___________Geometric Design
The 24-hour traffic volume count at any station on a specific day in any month of the year is adjusted to Average Daily Traffic (ADT) as __________,…Traffic Engineering
The instantaneous speed of a vehicle at a specified cross-section or location is called asTraffic Engineering
For the purpose of checking the requirement of highway geometric design elements, _________ is generally taken as the design speed of the existing…Traffic Engineering
Which of the following statement(s) is/are incorrect regarding methods used for Origin–Destination (O–D) survey? (i) Floating car method (ii) License…Traffic Engineering
A subgrade soil sample is tested using standard CBR apparatus and the load values are observed as 60 kg for 2.5 mm penetration and 80 kg for 5 mm…Highway Materials
Temperature stresses can induce cracking in cement concrete pavements. If a slab undergoes uniform cooling, where is the crack most likely to develop…Pavement Design
According to the position of bridge floor relative to the formation level and the highest flood discharge level, the bridges are classified asBridge Engineering
The Indian Roads Congress (IRC) code that is used for identifying or numbering the culverts and bridges isBridge Engineering
While selecting a site for a major river bridge, a deep gorge with high rocky cliffs on both sides is being evaluated. Compared to a wide alluvial…Bridge Engineering
________ is adopted when it is desired to provide only for angular movement of the girder which is fixed to the top shoe.Bridge Engineering
For a bridge to be built across a tidal estuary, which of the following site conditions is most critical in determining the minimum vertical…Bridge Engineering
_________ is most suited for compacting dry cohesionless granular material in road construction.Highway Construction
IRC recommended camber for thin bituminous surface in a light rainfall area isGeometric Design
What are the two main categories of embankment slopes ?Geometric Design
Match the following lists : List I (Median widths at intersections): P. Four feet or wider Q. Twenty-eight feet or wider R. Sixteen feet or wider S.…Traffic Engineering
If Vd is design speed (mph), t_p-r is perception-reaction time (sec), a is deceleration rate (ft/sec²) and G is longitudinal grade of the road…Sight Distance
If Vd is design speed (mph), e_max is maximum rate of superelevation, f_max is co-efficient of side friction. What is the expression for minimum…Geometric Design
What is the major difficulty in establishing human surveillance in freeway management systems ?Traffic Engineering and Road Safety
The weighted average of the damages caused by the individual axle load group with respect to the corresponding volume of the traffic of each group is…Pavement Design
Which one of the following is a factor that is to be multiplied by the total traffic repetitions in a lane to convert it to equivalent repetitions…Pavement Design
Q.1 For a railway track, the width of the formation depends upon which of the following? i. Type of sleepers ii. Type of ballast iii. Type of gauge…Railway Engineering
Q.5 Which of the following is NOT a way by which traffic volume data is presented?Traffic Engineering
Q.8 The type of signal in which the timings of the phase and cycle are changed according to traffic demand is calledTraffic Signal Design
Q.15 Consider the following distances: d₁ = distance travelled by the vehicle after applying the breaks. d₂ = distance travelled by overtaking…Sight Distance
Q.29 A vehicle was stopped by fully jamming the breaks in 1.8 s and the skid marks measured 9 m. Determine the average skid resistance. Take g = 10…Highway Materials
Q.46 In expansion joints, the loads are transferred through:Pavement Design
Q.51 A BG track is laid with a sleeper density of N + 3. The width of the sleeper is 20.25 cm. Find the minimum depth of the ballast cushion.Railway Engineering
Q.86 The type pavement marking which is used as a hazard marking and guide marking for safe driving during night is known asTraffic Engineering
Which of the following does NOT represent the grade of Bitumen based on viscosity?Highway Materials
If the 30th highest hourly volume is adopted for design, there will be congestion on road for only:Traffic Capacity
Traffic engineering does NOT include which of the following? i.Geometric design ii.Traffic studies and analysis iii.Road user characteristics…Traffic Engineering
As per IS 1203-1978 in the penetration test of bitumen, a standard tapered needle is used to calculate:Highway Materials

← Previous5 / 6Next →